This class meets a half day per week for 9 weeks. Class size is limited to 15 due to the hands-on nature. Much of the time will be spent in our live-fire lab which includes furnaces, boilers, A/C, etc.

Please bring hand tools, electrical meter (volts and amps), digital dual-port manometer, and R-454b gauges to class each week.

Module 1 - ABCs of Comfort

Module 2 - Basic Electrical Troubleshooting - read wiring diagrams, use a volt meter, measure amperage

Module 3 - Furnace Component Break Down plus Clean & Check - furnaces in the lab will be disassembled and re-assembled then we utilize O&M manuals to properly clean furnaces and check safeties

Module 4 - Furnace Troubleshooting - how to use a manometer or mag gauge to measure pressure, troubleshooting with a voltmeter, reading error codes, adjusting airflow, etc.

Module 5 - Boiler Service - component identification, basic piping, and how to clean a boiler

Module 6 - A/C and Heat Pump Charging & Maintenance - basic operation and troubleshooting, using refrigerant gauges and superheat to check charge arrangement

Module 7 - Ecobee Smart Thermostats - install, setup, and programming

Module 8 - Ductless Mini-split Installation and Service

Module 9 - Indoor Air Quality (IAQ) Basics – Filtration, Evolution/Infinity air purifier, UV lights, PCO duct air purifiers, and bi-polar ionizers for functions, installation, and maintenance

Must attend at least 6 modules to earn 24 "FAD Distributor" or "Elite Distributor" hours.

Each module earns 4 NATE hours (except module 1) and credit can be awarded individually for each module. Note: smart stat module is only 3 NATE hours.

NATE course IDs:

Electrical #8532-0007

Furnace Clean #8532-0010

Furnace Service #8532-0003

Boiler #8532-0008

A/C & HP #8532-0001

Smart stats #8532-0017

Ductless #8532-0022

IAQ #8532-0012

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

OVERVIEW:This training course provides the participants with an overview of Carrier/Bryant 37MU and Heil/Day&Night D5CU Crossover units which allow the usage of a horizontal discharge mini-split inverter with a standard furnace or air handler fan coil. The course will include installation requirements, operating characteristics and a general overview of service and troubleshooting procedures.

WHO SHOULD ATTEND:The target audience includes HVAC technicians and installers. Attendees should have a general understanding of air conditioning systems, refrigerants, installation and service procedures.

REQUIRED TOOLS: electrical meter with micro-leads and basic hand-tools

OUTLINE:

- Introduction of product (including models, capacities, voltages, etc.)

- Application of R-454B refrigerant

- Installation requirements and procedures

- Operating characteristics

- Fault codes

- Servicing and Diagnostic procedures

- Refrigerant piping lengths and charging procedures

- Installation wiring (standard thermostat or communicating)

This classes qualifies for 4 "FAD Distributor" or "Elite Distributor" hours for the dealer and 4 NATE hours for the technician

NATE course ID# 8532-0028, NATE credit received through this course is associated with the following specialties: A/C Install, A/C Service, Air Distribution Install, Air Distribution Service, Air to Air Heat Pump Install, Air to Air Heat Pump Service, Certified HVAC Professional, Efficiency Analyst Senior, HVAC Performance Verifier, Light Commercial Refrigeration Install, Light Commercial Refrigeration Service, Low GWP Refrigerants 

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

Upon completion of this course, contractors will be enrolled in the Carrier Controls Experts program at Silver level certification.

Laptop Required and NEED to have a copy i-Vu Tech Tools 10.0.  Please contact Joe Conkle for assistance (708-418-7840 or jconkle@tecmungo.com)

Lunch will be served each week. Some weeks will conclude at 1pm after lunch and other weeks will go until 3pm, depending on that weeks topic.

WEEK 1 – Bacnet Networking Basics & Intro to the Carrier Service Tools

WEEK 2 - RTU OPEN Controller

WEEK 3 - VVT OPEN Controllers

WEEK 4 - UPC OPEN & Custom Programmable Controllers

WEEK 5 - VAV OPEN Controllers

WEEK 6 - i-Vu OPEN Web Interface & Certification Testing

Carrier OPEN BACnet Controls & Service Tools

We will discuss the Basics of bacnet networking, the Carrier OPEN product line, different controllers / sensors you may see in the field, make sure everyone has the software loaded on their laptops, and can successfully connect to controllers.

RTU OPEN Controller

We will discuss installation and wiring, sequence of operation, programming, commissioning, service, and troubleshooting. This is for constant volume and Staged Air Volume (SAV) RTU under 25 tons.

VVT OPEN Controllers

We will discuss installation and wiring, sequence of operation, programming, commissioning, service, and troubleshooting for Variable Volume and Temperature (VVT) zoning systems.

UPC OPEN Controllers

We will discuss the equipmentbuilder software and its uses with many of the controllers in the carrier product line. This includes many different applications including hot & Chilled water plants, chillers, boilers, condensing units, fan coils, and RTUs greater than 25 tons.

VAV OPEN Controllers

We will discuss installation and wiring, sequence of operation, programming, commissioning, service, and troubleshooting for Variable Air Volume (VAV) systems.

i-Vu OPEN Web Interface

We will discuss installation, programming, commissioning, service, and troubleshooting for Carriers web-based interface tools. Custom graphics will not be covered in this particular course but a follow-up course is offered to introduce you to the Viewbuilder tool.

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

OVERVIEW:This training course provides the participants with an overview of Carrier/Bryant 37MU and Heil/Day&Night D5CU Crossover units which allow the usage of a horizontal discharge mini-split inverter with a standard furnace or air handler fan coil. The course will include installation requirements, operating characteristics and a general overview of service and troubleshooting procedures.

WHO SHOULD ATTEND:The target audience includes HVAC technicians and installers. Attendees should have a general understanding of air conditioning systems, refrigerants, installation and service procedures.

REQUIRED TOOLS: electrical meter with micro-leads and basic hand-tools

OUTLINE:

- Introduction of product (including models, capacities, voltages, etc.)

- Application of R-454B refrigerant

- Installation requirements and procedures

- Operating characteristics

- Fault codes

- Servicing and Diagnostic procedures

- Refrigerant piping lengths and charging procedures

- Installation wiring (standard thermostat or communicating)

This classes qualifies for 4 "FAD Distributor" or "Elite Distributor" hours for the dealer and 4 NATE hours for the technician

NATE course ID# 8532-0028, NATE credit received through this course is associated with the following specialties: A/C Install, A/C Service, Air Distribution Install, Air Distribution Service, Air to Air Heat Pump Install, Air to Air Heat Pump Service, Certified HVAC Professional, Efficiency Analyst Senior, HVAC Performance Verifier, Light Commercial Refrigeration Install, Light Commercial Refrigeration Service, Low GWP Refrigerants 

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

This class is normally only taught in Indianapolis for $1,600 but is being offered this year in Melrose Park for $895 PLUS it also includes the $450 diagnostic tool. This is a limited time class price and tool inclusion.

This 3-day training course is only one portion of the requirements to become certified by Carrier or Bryant. There are also 4 online training modules, as well as as business requirements (signed agreement, insurance, brand loyalty, etc), and you must already be a Bryant or Carrier FAD.

Included: Handheld Midea/Carrier Ductless Diagnostic Service Tool ($450 value) and Lunch for 3 days

Ductless & Crossover Foundations:Installation & Start-up

In this course, participants will learn about the proper application, installation, startup, and basic troubleshooting of Ductless and Crossover Solutions. After completing this course, the participants will be able to: 

- Demonstrate an understanding of DLS technology, equipment and application​

- Interpret and apply installation instructions and installation techniques

- Demonstrate and apply accepted DLS best practices​

- Perform DLS system start up and commissioning

- Evaluate existing installations to avoid problems 

REQUIRED TOOLS: torque wrench, R-410A/R-454B flaring tool, reamer, pipe cutter, 2 adjustable wrenches, electrical meter with micro-leads, and basic hand-tools

This class qualifies for 24 "FAD Distributor" or "Elite Distributor" hours for the dealer and 16 NATE hours for the technician

NATE course ID# 8532-0027

NATE credit received through this course is associated with the following specialties: Air Conditioning Installation, Air Conditioning Service, Air Distribution Installation, Air Distribution Service, Air to Air Heat Pump Installation, Air to Air Heat Pump Service, Certified HVAC Professional, Efficiency Analyst Senior, Gas Heating (Air) Installation, Gas Heating (Air) Service, HVAC Performance Verifier, Hydronics Gas Installation, Light Commercial Refrigeration Installation, Light Commercial Refrigeration Service, Low GWP Refrigerants

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

PREREQUISITE: Carrier OPEN BACnet Controls Series I or instructor approval

WEEK 1 - Intro to SNAP Custom Programming

Covers Understanding line & block programming, the basics of building a program, working with and configuring PID loops, reading the logic page

WEEK 2 - ViewBuilder Custom Graphics

Create Custom graphics and floorplans using the carrier viewbuilder program

WEEK 3 - Advanced SNAP Custom Programming

Formatting properties pages & 3rd party integration

Lunch will be served each week.

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.