Your browser is not optimized for viewing this website.

More information »

TEC & Excelsior Training

Filter by Category



Our Classes

Carrier OPEN BACnet Controls Series Level I (hands-on) - Melrose Park, IL

$2,975

with Joe Conkle

Calendar Oct 16, 2025 at 8 am, runs for 6 weeks

This course is REQUIRED for Carrier Expert CS certification.

Laptop Required and NEED to have a copy i-Vu Tech Tools 9.0 and Field Assistant service tool.  Please contact Joe Conkle for assistance (708-418-7840 or jconkle@tecmungo.com)

Lunch will be served each week. Some weeks will conclude at 1pm after lunch and other weeks will go until 3pm, depending on that weeks topic.

WEEK 1 - Carrier OPEN BACnet Controls & Service Tools

WEEK 2 - RTU OPEN Controller

WEEK 3 - VVT OPEN Controllers

WEEK 4 - UPC OPEN Controllers

WEEK 5 - VAV OPEN Controllers

WEEK 6 - i-Vu OPEN Web Interface

Carrier OPEN BACnet Controls & Service Tools

We will discuss the Carrier OPEN product line, different controllers / sensors you may see in the field, and then make sure everyone has the software loaded on their laptops, and can successfully connect to controllers.

RTU OPEN Controller

We will discuss installation and wiring, sequence of operation, programming, commissioning, service, and troubleshooting. This is for constant volume and Staged Air Volume (SAV) RTU under 25 tons.

VVT OPEN Controllers

We will discuss installation and wiring, sequence of operation, programming, commissioning, service, and troubleshooting for Variable Volume and Temperature (VVT) zoning systems.

UPC OPEN Controllers

We will discuss installation and wiring, sequence of operation, programming, commissioning, service, and troubleshooting. This is for chillers, condensing units, and RTUs greater than 25 tons.

VAV OPEN Controllers

We will discuss installation and wiring, sequence of operation, programming, commissioning, service, and troubleshooting for Variable Air Volume (VAV) systems.

i-Vu OPEN Web Interface

We will discuss installation and wiring, sequence of operation, programming, commissioning, service, and troubleshooting for Carriers web-based interface tool. Custom graphics will not be covered in this particular course but a follow-up course is offered to introduce you to the Viewbuilder tool.

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

3 to 27 ton RTUs with Vane Axial Fans - NATE, FAD, & Elite hrs - Lansing, IL

$65

with Neil Stoeger

Calendar Oct 21, 2025 at 8 am

Times are changing and the current code requirements for high IEERs are driving the market to use Staged Air Volume (SAV) in place of the traditional constant volume systems.

Smaller units using vane axial fans with ECM motors are standard now, so we will cover this type of RTU from Carrier (EcoBlue), Bryant (Axion), and ICP (X-Vane).  This exclusive technology was designed to improve performance and efficiency while decreasing maintenance and installation costs. This RTU includes the industry’s first belt-less direct-drive vane axial fan for rooftop units, a new control board and coil technology, permanently lubricated motor bearings, tool-less filter access doors, and more.

Technicians need to know how to properly install, setup, and service all of these units, as they are now the standard RTUs in the market.

Topics covered include installation, start-up, and troubleshooting. We will discuss standard RTUs, ECM controlled SAV RTUs, airflow setup, vane axial fans, humidimizer, and economizers.

We will focus on Bryant, Carrier, & ICP SAV equipment in the 3 thru 27 ton range.

This classes qualifies for 4 NATE hours for the technician plus 4 "FAD Distributor" or "Elite Distributor" hours for the dealer.

NATE course ID# 8532-0014

 

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

Evolution Connex / Infinity Touch / Ion Controllers (hands-on) - NATE, FAD, & Elite hrs - Melrose Park, IL

$64

with Ryan Hoger

Calendar Oct 21, 2025 at 8 am

This is a hands-on class with 2-3 students per system. The class will cover the functionality of the Evolution, Infinity, and Ion communicating touch screen controls. We will also discuss unique installation requirements as related to zoning systems, variable speed outdoor units, and modulating gas valves.

Topics will include:

-Wiring and commissioning

-Service settings and adjustments

-Wi-Fi setup

-Advanced, smart setback

-Real-time weather display

-Website management tool

-Mobile app usage

This classes qualifies for 4 NATE hours for the technician plus 4 "FAD Distributor" or "Elite Distributor" hours for the dealer.

NATE course ID# 8532-0002

NATE credit received through this course is associated with the following specialties: A/C Install, A/C Service, Air Distribution Install, Air Distribution Service, Ht Pump Install, Ht Pump Service, Gas Heating Install, Gas Heating Service, Hydronics Install, Hydronics Service

 

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

Full Course

Aeroseal Duct Sealing with HomeSeal (hands-on) - NATE, FAD, & Elite hrs - Melrose Park, IL

$500

with Ryan Hoger

Calendar Oct 22, 2025 at 8 am

Note: There is no charge for dealers who wish to attend the Day 1 portion as a refresher. Contact rhoger@tecmungo.com for FREE REGISTRATION CODE. Make sure your HomeSeal machine is clean and operational BEFORE you bring it to class.

The training will be two days for new dealers. Day 1 will be at TEC and Day 2 will be on-site at a home. Each dealer should have their 2-man Aeroseal install crew attend both days. It is also suggested that your retail sales person (or whomever will be quoting Aeroseal systems) attend the morning portion of the 1st day at a minimum.

Day 1 Morning - Classroom training session

Day 1 Afternoon - Three dealers in the TEC lab each using their own HomeSeal machines simultaneously to seal the small duct systems that we have in the lab. The dealer needs to bring ALL of their Aeroseal equipment (machine, tablet, sealant, foam, air compressor, dryer, extension cords, EVERYTHING).

Day 2 All day - Single dealer doing a full seal at the residential home of their choice (preferably one of their own employees not a client). New dealers should already have been contacted about scheduling this date. If an existing dealer needs a field training refresher please contact the instructor to schedule.

Lunch will provided on the 1st day at the classroom.

This classes qualifies for 4 NATE hours for the technician plus 4 "FAD Distributor" or "Elite Distributor" hours for the dealer.

NATE course ID# 8532-0006 NATE credit received through this course is associated with the following specialties: A/C Install, A/C Service, Air Distribution Install, Air Distribution Service, Ht Pump Install, Ht Pump Service, Gas Heating Service, Gas Heating Install

 

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

Will run

Economizer Basics & Setup for Honeywell JADE & Siemens Climatix-ECO (hands-on) - NATE, FAD, & Elite hrs - North Aurora, IL

$64

with Ryan Hoger

Calendar Oct 23, 2025 at 8 am

Economizers have been increasingly required by energy code but many technicians have a set it and forget attitude about these devices. Sometimes they can be simple applications, but other times things can bite you.

This course will examine the following:

1. Technology Overview

2. Dry bulb vs. Enthalpy

3. IECC Code Requirements (including local law)

4. Typical Energy Savings

5. CO2-based Demand Controlled Ventilation (DCV)

6. Honeywell JADE Economizer Controller Wiring

7. Hands-on Setup and Configuration of JADE on the workbench

8. Overview of MicroMetl's Siemens Climatix-ECO Controller

This classes qualifies for 4 NATE hours for the technician plus 4 "FAD Distributor" or "Elite Distributor" hours for the dealer.

NATE course ID# 8532-0009

NATE credit received through this course is associated with the following specialties: A/C Install, A/C Service, Air Distribution Install, Air Distribution Service, Ht Pump Install, Ht Pump Service, Gas Heat Install, Gas Heat Service, Light Commercial Install, Light Commercial Service

 

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

Gas Furnace 102: Service & Troubleshooting (hands-on) - NATE, FAD, & Elite hrs - Lansing, IL

$70

with Dave Herman

Calendar Oct 24, 2025 at 8 am

Students MUST first attend Gas Furnace 101 or have instructor approval to skip into this more advanced class.

This course offers familiarization of the troubleshooting and installation manuals followed by a hands-on training session. The lab work will include start-up and troubleshooting procedures of residential gas furnaces. Students will be working on fully function systems in the lab area.

Please bring hand tools, volt or multi-meter, and manometer (or magnahelic).

This classes qualifies for 4 NATE hours for the technician plus 4 "FAD Distributor" or "Elite Distributor" hours for the dealer.

NATE course ID# 8532-0003

NATE credit received through this course is associated with the following specialties: Gas Heating Install, Gas Heating Service

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

Certified Ductless Pro - NATE, FAD, Elite, & ComEd hrs - Melrose Park, IL

$875

with Andy Sias

Calendar Oct 28, 2025 at 8 am

LIMITED - INVITE ONLY - LIMITED - INVITE ONLY - You must work for a Carrier/Bryant Factory Authorized Dealer (FAD) to register for this class.

This class is normally only taught in Indianapolis for $1,600 but is being offered this season in Melrose Park for $875 PLUS it also includes the $450 diagnostic tool. This is a limited time class price and tool inclusion.

This 3-day training course is only one portion of the requirements to become certified by Carrier or Bryant. There are also 4 online training modules, as well as as business requirements (signed agreement, insurance, brand loyalty, etc), and you must already be a Bryant or Carrier FAD.

Included: Handheld Midea/Carrier Ductless Diagnostic Service Tool ($450 value) and Lunch for 3 days

 

Ductless & Crossover Foundations:Installation & Start-up

In this course, participants will learn about the proper application, installation, startup, and basic troubleshooting of Ductless and Crossover Solutions. After completing this course, the participants will be able to: 

- Demonstrate an understanding of DLS technology, equipment and application​

- Interpret and apply installation instructions and installation techniques

- Demonstrate and apply accepted DLS best practices​

- Perform DLS system start up and commissioning

- Evaluate existing installations to avoid problems 

REQUIRED TOOLS: torque wrench, R-410A/R-454B flaring tool, reemer, pipe cutter, 2 adjustable wrenches, electrical meter with micro-leads, and basic hand-tools

 

This classes qualifies for 24 "FAD Distributor" or "Elite Distributor" hours for the dealer and 16 NATE hours for the technician

 

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

Combustion Analysis for Condensing Boilers... with Bill & Bill (hands-on) – NATE hrs – Melrose Park, IL

$45

with Bill Shanel

Calendar Oct 28, 2025 at 8 am

Join both of our "Hydronic Bills," Bill Bailey & Bill Shanel, as they guide you on the proper usage of a combustion analyzer to setup popular models of various condensing boilers.

This course is focused toward the understanding of combustion diagnostics and adjustments to improve efficiency, performance and reliability, as well as troubleshooting and diagnosis. Aspects of combustion from basic theory to verification of manufacturer’s specifications and flue gas diagnostics testing are covered. Measurement of oxygen, carbon dioxide, carbon monoxide, nitric oxides and sulfur oxides round out the dynamics of assuring efficient combustion. Controlling fuel, flame temperature, excess air and draft are detailed to maximize efficiency without sacrificing safety.

Bring your combustion analyzer with you to class for use in our lab. We will be working on HTP and IBC Condensing Boilers.

This classes qualifies for 4 NATE hours for the technician.

NATE course ID# 8532-0023, NATE credit received through this course is associated with the following specialties: A/C Install, A/C Service, Ht Pump Install, Ht Pump Service, Gas Heating Install, Gas Heating Service, Hydronics Gas Install, Hydronics Gas Service, Certified HVAC Pro, Efficiency Analyst Senior, HVAC Performance Verifier

-------------------------------------------------------------------------------

CANCELLATION POLICY - To cancel out of a class, please email ryan.hoger@tecmungo.com with your name and the date of the class.  Refunds are available (with a 15% processing fee) up to 72 hours before the start of class.  You may also substitute a student from the same company (without penalty) at any time.

Will run





Forgot password?
Staff Log In